Dallas Insulation



Attic Cleaning Services: Attic Cleanup and Decontamination

rats in attic insulation

The chances are pretty high that at some point you will have rats, mice, squirrels, raccoons, nests or other pest infestation in your attic. These pests can carry many diseases that are harmful to most humans and especially to children. It is important that you will want to protect yourself and your family from being exposed the health risks and diseases these pests bring.

Attic Cleaning Costs

To reduce the risk that your family will get infected as much as possible, you will want to contact an attic insulation removal and decontamination company. They will be best to advise you on the extent of the damage, contamination and remediation costs.

Cleaning costs will vary depending on the above factors as rodents can cause an extreme amount of damage to your home. A professional service will come and inspect your attic and provide you with a free estimate.

Attic Insulation Contamination

These pests, usually rodents, leave droppings and urine that contaminate attic areas. These can seep into and contaminate your attic’s insulation or into the foundations of the house itself. These droppings and urine may contain the harmful diseases that if kept unchecked may spread and infect your household.

You will want to safely remove attic insulation them from your household and you will need to take measures to pest proof your attic to prevent them returning.

Some other pests that may infest your attic aside from rats are opossums, raccoons and even bats. These animals may nest in your attic and breed which can spell potential danger to your home.

These pests may bring Hantavirus, Leptospirosis, Murine Typhus and even Salmonella which can infect your family and may not even be detected right away.

Attic Clean Up

You need to take precaution before and while you are cleaning up the rodent-infested areas. What we first suggest is if you find your home to be infested with pests is that you consult a professional in how you can get rid of rodents and other pests that may have made a home in your attic.

Once you have gotten rid of the pests, you will then need to make sure you seal up any entrances or holes that the rodents or other pests used to get in. You will need to get them out first before you begin the decontamination process. Make sure to air out the room first for at least 30 minutes before you decontaminate to allow fresh air to enter the area.

Attic Cleaning

When you start attic cleaning, it is important that you don’t stir up the dust in the room by vacuuming or sweeping up the droppings or urine. You do not want the contaminants to spread to the air. Make sure to wear protective clothing, a respirator and cleaning gloves (vinyl, latex or rubber gloves) when cleaing up.

Make sure to spray the droppings and the urine with disinfectant along with a mixture of water and bleach. It is suggested you let it soak for about 5 minutes. The recommended solution of the bleach is one part bleach to 10 parts water. For commercial disinfectants, make sure to follow the instruction on the label for the recommended solution.

Use a paper towel to clean the area of droppings and urine. Make sure to clean everything up and then dispose the waste in a garbage bag that you can throw out right away. You do not want it to linger inside your house.

After cleaning up the area, make sure to disinfect again the area and wipe clean. You might also want to disinfect the entire attic to ensure that all places are covered which might have been contaminated in the past.

For a full attic cleaning and insulation service contact:

Dallas Insulation
3901 Arlington Highlands Blvd Ste 200
Arlington TX 76018
(817) 784-7747

“Originally Publised Article Here: Insulation Contractor Arlington TX

Source: http://dallas-insulation.com/attic-cleaning-services-attic-cleanup-and-decontamination/

Types of Insulation Material

In this video you will learn about the different types of insulation, how much to use and how to take advantage of state rebates and special pricing.

Most people, when they think about energy saving consider updating their heating or air conditioning unit and windows. While those are a part of reducing energy cost, upgrading the home insulation is by far the most cost effective energy upgrade. Learn more about the benefits of different insulation types in this video.

For more information on the best types of insulation for your Dallas home, give us a call for a free no-obligation consultation.

Dallas Insulation
3901 Arlington Highlands Blvd Ste 200
Arlington TX 76018
(817) 784-7747


Residential Insulation Contractor Dallas/Fort Worth/Plano Areas

More resources:

Thermal Insulation

“Originally Publised Here: Insulation Contractor Richardson TX

Source: http://dallas-insulation.com/types-of-insulation-material-dallas/

New Green Home Options Dallas TX

Check out the new LEED home (Leaders in Energy and Environmental Design). LEED sets the standards for green, environmentally friendly and energy conserving home construction.

Energy saving methods used in LEED home construction include:
• Solar panels to reduce electricity bill
• Grey and rainwater collection system for use in lawn watering
• Special bio-friendly insulation – Spray foam insulation
• Water conserving landscaping  include heat and drought resistant plants
• Energy star appliances and low-energy light bulbs

“Original Post Source Here: Insulation Contractor Duncanville TX

Source: http://dallas-insulation.com/new-green-home-options-dallas-tx/

Dallas Insulation Contractor Service Areas

Addison TX Alvarado TX Argyle TX Arlington TX Azle TX Balch Springs TX Bedford TX Burleson TX Carrollton TX Cedar Hill TX Cleburne TX Colleyville TX Coppell TX Crowley TX Dallas TX Duncanville TX Ennis TX Euless TX Flower Mound TX Fort Worth TXGarland TX Godley TX Granbury TX Grand Prairie TX Grapevine TX Haltom City TX Haslet TX Hillsboro TX Hurst TX Irving TX Italy TX Joshua TX Keller TX Kennedale TX Lake Dallas TX Lancaster TX Lewisville TX Mansfield TX Mesquite TX Midlothian TX North Richland Hills TX Plano TX Red Oak TX Rhome TX Richardson TX Roanoke TX Seagoville TX Southlake TX Sunnyvale TX The Colony TX Venus TX Waxahachie TX

Dallas Insulation
3901 Arlington Highlands Blvd Ste 200
Arlington TX 76018
(817) 784-7747

Original Post Source Here: Insulation Contractor Lake Dallas TX

Source: http://dallas-insulation.com/dallas-insulation-contractor-service-areas/

Best Home Insulation | Dallas | Fort Worth | Plano

Best House Insulation
With the soaring energy costs of heating and cooling your home today, it’s more important than ever before to ensure you have the best home insulation. In some older homes that were built back some seventy or eighty years ago, you may not have any insulation at all in the walls, and very little attic insulation. Although the costs of re-insulating an existing home are much greater then new home construction, the long term benefits in reduced heating and cooling costs will make up the difference.

Insulation Types

Today’s insulation comes in many different forms as far as the ways in which they are applied, and the materials that are used in their manufacturing. You can use the standard fiberglass pink insulation that is synonymous with Owens Corning who also offers attic blanket insulation for unfinished attics, to spray on foam, and rigid foam as well. Each type provides for different uses, and each type will have a different ‘R’ value. The ‘R’ value is the rating system that determines the insulation over all heat reducing qualities. The higher the ‘R’ value, the better insulator it will be.

Batt Insulation

The classic fiberglass insulation comes in what are known as ‘batts’. Usually in four foot by one and a half foot strips. These are designed to fit nicely in between the studs of a wall. They should fit snugly into the wall, but should never be compressed to fit. When you compress fiberglass insulation it loses much of its ‘R’ value. They are also very easy to cut to fit with the use of a sharp utility knife.

Spray Foam Insulation

Spray Foam Insulation

If you’re insulating a building or a basement where the looks are not important, such as a warehouse, then the best solution would be to use a spray on foam insulation. This foam can be sprayed over-top the existing interior of the building, it then expands and dries to form a well sealed surface. This is a nice option because it can get into all those small, unnoticed cracks and holes that may allow for heat loss. You can find spray foam insulation in an open cell or closed cell foam. While the open cell is less expensive, it is also less dense and therefore will have less of an ‘R’ value.

Rigid Foam Board Insulation

Rigid foam board insulation is often used on the exterior of the home or building. It is installed first, and then the siding is applied over top. Some siding companies like Alcoa, have designed a siding product that combines both. It has the foam insulation bonded directly to the siding itself. This will allow you to save a lot of time during the installation process.

Blown in Insulation

Another common type used in attics is a loose fill, or blown in insulation. Blown in insulation can be made of fiberglass, rock wool or cellulose. It is pumped in through a hose and blown in to the desired location. The ‘R’ value of this type is measured by how thickly it is blown in. Obviously, the thicker it is, the higher the ‘R’ value is. There is also garage door insulation as well as insulation for individual components such as gasket insulation.

Insulation in Your Home

In order to get the best possible insulating qualities that will serve your purposes, you’ll have to go out and do a little research. Going online is a great place to start, as you can have the information right at your finger tips for easy comparison. If you’re looking for ways to save money, not only in the cold winter months, but also in the hot simmer ones, then improving the insulation in your home is the first place you need to start.


Dallas Insulation
3901 Arlington Highlands Blvd Ste 200
Arlington TX 76018
(817) 784-7747


Best Home Insulation Dallas | Fort Worth | Plano

Article Source Attic Insulation Dallas – Fort Worth DallasInsulation.com

Source: http://dallas-insulation.com/best-home-insulation-dallas-fort-worth-plano/

What is Radiant Barrier Insulation

What are radiant barriers?

radiant barrier insulation

Fitting Radiant Barrier Insulation Into Roof Of New Home

Radiant barriers are materials that are installed in buildings (can be in walls or roof) to reduce heat during summer time and to keep the heat loss in winter, and hence to reduce building or home heating and cooling energy usage and electric bills to keep the environment safe.

The potential benefit of attic radiant barriers or radiant barrier insulation is primarily in reducing air-conditioning cooling or warming loads in warm or hot climates respectively. Radiant barriers usually consist of a thin sheet or coating of a highly reflective material, normally aluminum, applied to one or both sides of a number of materials.

This material includes Kraft paper, plastic films, cardboard, plywood sheathing, and air infiltration barrier material depending on the construction.

Types of radiant barriers

A radiant barrier utilizes aluminum foils to reduce heat gains and losses during summer and winter respectively. They mainly are used under roof in the attic area.

Radiant barriers come in many forms and shapes for different applications:

  • Single-sided foils backed by a supportive material like polypropylene or Kraft paper
  • Foil-faced roof sheathings like foil-laminated OSB
  • Double-sided foils with a strengthening material between the layers like polyethylene bubble-pack
  • Foil-faced insulation (reflective insulation)
  • Multi-layered foils; and radiant barrier chips

How to install a radiant barrier

Radiant barriers may be installed in attics in several different ways depending on the construction.

The simplest and easiest is to install the radiant barrier directly on top of existing attic insulation, with the reflective side facing up. The facing upside will reflect the heat waves coming from the roof top. This is normally called the attic floor application in builders’ terms.

Another way to install a radiant barrier is to attach it near the roof. The roof application has several different variations.

  1.  hook the radiant barrier to the bottom surfaces of the attic truss chords or rafter framing
  2. drape the radiant barrier over the tops of the rafters before the roof deck is applied
  3. attach the radiant barrier directly to the underside of the roof deck in the attic.

Depending on the construction of the house, there can be several different ways to install radiant barrier insulation. Make sure to consult with an expert and chose the most cost effective way of installation.

How radiant barriers works

Radiant barriers perform a function that is similar to that of conventional roof insulation, in that they reduce the amount of heat that is transferred from the attic into the house through heat waves from the sun.

They vary in the way they lower the heat flow. Radiant barrier insulation reduces the amount of heat radiated across an airspace that is right next to the radiant barrier.

The primary function of conventional roof insulation is to trap still air within the insulation and hence reduce heat transfer by air movement in the attic area. The insulation fibers, chips or particles also partially block radiation heat transfer through the space occupied by the insulation.

Upwards of 90% of ceiling heat gain in summer months can be attributed to heat from the attic space above caused by radiant energy transferred by the sun. The radiant heat from the sun is engrossed by roofing shingles and transmitted it to the roof decking beneath and into the attic space. Conventional roof insulation absorbs much of this heat and six times its saturation point has been met, this heat is then transferred to the living spaces below through the ceiling.

When stapled to the bottom of roof rafters in an attic space, radiant barrier insulation can block 90% of the radiant heat from the roofing surface during summer time which in turn lowers overall attic temperatures by 35 degrees bringing the attic temperature closer to the true outdoor temperature or even lower.

By lowering the temperature in your attic, you can reduce the amount of heat transferred to your living spaces below by up to 45% giving you greater comfort in your home and reducing the load on your air conditioning unit. No matter what radiant barrier insulation you select, make sure to read radiant barrier insulation reviews before picking the right brand of the product.

The cost of a radiant barrier in Dallas/Fort Worth Texas

A radiant barrier costs within ranges of 10 cents to $25 per sq. ft for a single-sided barrier and $45 to $1 per sq. ft for double-sided ones. This, however, does not include labor costs for installation. Normally, the cost of installing a radiant barrier in Texas, USA ranges between 10 cents to $1 per sq. ft. The total cost may be around $300-$500 for a 1,500 sq. ft attic area. Most importantly, keep in mind that costs will always vary.

Read Full Source Article Here: Best Dallas Insulation Contractors

Source: http://dallas-insulation.com/radiant-barrier-insulation/